everlight electronics co.,ltd. everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 1 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao technical data sheet 0805 package chip led(1.1mm height) 17-21/G6C-AP1Q1B/3t features ? package in 8mm tape on 7 diameter reel. ? compatible with automatic placement equipment. ? compatible with infrared and vapor phase reflow solder process. ? mono-color type. ? pb-free. ? the product itself will remain within rohs complaint version descriptions ? the 17-21 smd taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ? besides, lightweight makes them ideal for miniature applications. etc. applications ? telecommunication: indicator and backlighting in telephone and fax. ? flat backlight for lcd, switch and symbol. ? general use. device selection guide chip part no. material emitted color lens color 17-21/G6C-AP1Q1B/3t algainp brilliant yellow green water clear
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 2 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao package outline dimensions - + note: the tolerances unless mentioned is 0.1mm ,unit = mm
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 3 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao absolute maximum ratings (ta=25 ) parameter symbol rating unit reverse voltage v r 5 v forward current i f 25 ma operating temperature topr -40 ~ +85 storage temperature tstg -40 ~ +90 electrostatic discharge(hbm) esd 2000 v power dissipation p d 60 mw peak forward current (duty 1/10 @1khz) i fp 60 ma soldering temperature tsol reflow soldering : 260 for 10sec. hand soldering : 350 for 3 sec. electro-optical characteristics (ta=25 ) parameter symbol min. typ. max. unit condition luminous intensity i v 45.0 ----- 90.0 mcd viewing angle 2 1/2 ----- 140 ----- deg peak wavelength p ----- 575 ----- nm dominant wavelength d 570.0 ----- 574.5 nm spectrum radiation bandwidth ----- 20 ----- nm forward voltage v f 1.75 ----- 2.35 v i f =20ma reverse current i r ----- ----- 10 a v r =5v notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forward voltage 0.1v
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 4 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao bin range of dom. wavelength group bin min max unit condition c16 569.5 571.5 c17 571.5 573.5 c18 573.5 575.5 a c19 575.5 577.5 nm i f =20ma bin range of luminous intensity bin min max unit condition p1 45.0 57.0 p2 57.0 72.0 q1 72.0 90.0 mcd i f =20ma bin range of forward voltage group bin min max unit condition 0 1.75 1.95 1 1.95 2.15 b 2 2.15 2.35 v i f =20ma notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forward voltage 0.1v
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 5 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao typical electro-optical characteristics curves
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 6 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao xxxxxx xxxxxx xxxxxxxxxxxx xxxx xxxxxxxx rohs label explanation cat: luminous intensity rank hue: dom. wavelength rank ref: forward voltage rank reel dimensions note: the tolerances unless mentioned is 0.1mm ,unit = mm
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 7 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao carrier tape dimensions: loaded quantity 3000 pcs per reel note: the tolerances unless mentioned is 0.1mm ,unit = mm moisture resistant packaging label aluminum moisture-proof bag desiccant label
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 8 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao reliability test items and conditions the reliability of products shall be satisfied with items listed below. confidence level 90% ltpd 10% no. items test condition test hours/cycles sample size ac/re 1 reflow soldering temp. : 260 5 min. 5sec. 6 min. 22 pcs. 0/1 2 temperature cycle h : +100 15min 5 min l : -40 15min 300 cycles 22 pcs. 0/1 3 thermal shock h : +100 5min 10 sec l : -10 5min 300 cycles 22 pcs. 0/1 4 high temperature storage temp. : 100 1000 hrs. 22 pcs. 0/1 5 low temperature storage temp. : -40 1000 hrs. 22 pcs. 0/1 6 dc operating life i f = 20 ma 1000 hrs. 22 pcs. 0/1 7 high temperature / high humidity 85 / 85%rh 1000 hrs. 22 pcs. 0/1
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 9 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao precautions for use 1. over-current-proof customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 60%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package. 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
everlight electronics co.,ltd. 17-21/G6C-AP1Q1B/3t everlight electronics co., ltd. http://www.ev erlight.com rev. 1 page: 10 of 10 device no:szdse-171-g16 prepared date:17-oct-2005 prepared by:liu tao 4.soldering iron each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the da mage of the product is often started at the time of the hand solder. 5.repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be damaged by repairing. e verlight electronics co., ltd. tel: 886-2-2267-2000, 2267-9936 office: no 25, lane 76, sec 3, chung yang rd, fax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiw an, r.o.c http://www.everlight.com
|
